11 BMW 1977 R100RS Replace Rocker Needle Bearings, Remove Valves & Inspect

After removing the heads, I found loose needle bearings from one of the rocker arm assemblies. This is not uncommon. The needle bearing cage has a lip that folds over the top and bottom of the cage to contain the needle bearings in the cage. According to Bob Fleischer in an Email to me:

“The cage is a metal sleeve that is rolled-over and inwards at the ends, forming a captive area for the needles [BROOK: What I call the “lip”]. The rolling wasn’t enough, and the cage was riding on the shaft, breaking at the rolled end.”

The lip has broken off on the left exhaust rocker arm and I find needle bearings inside the valve cover as I remove the pillow block on the rocker shaft that attaches the rocker assembly to the head. But, not all the needles can be accounted for. I presume someone did what I just did, lost some needles down the push rod tubes, and just put what needles they had in the damaged cage and put it all back together again.

Left Exhaust Rocket-Bottom Rocker Needle Bearing Cage Damaged

Left Exhaust Rocket-Bottom Rocker Needle Bearing Cage Damaged

Left Exhaust Rocker- Bottom Needle Bearing Cage Lost Its Needles

Left Exhaust Rocker- Bottom Needle Bearing Cage Lost Its Needles

Left Exhaust Lower Rocker-Recovered Needle Bearings and Cage Pieces

Left Exhaust Lower Rocker-Recovered Needle Bearings and Cage Pieces

Left Exhaust Lower Rocker-Recovered Needle Bearings and Cage Pieces

Left Exhaust Lower Rocker-Recovered Needle Bearings, Some Broken, and Pieces of The Cage Lip (Tooth Pick For Scale)

I wasn’t able to find all the needle bearings inside the valve cover. There should be 31 needles in the bearing cage. It’s not uncommon for them to fall down into the oil pan through the push rod tubes. They don’t cause any problems as they just sit in the pan.  When I removed the oil pan, I found the missing bearings.

Rocker Arm Bearings in Bottom of Oil Pan

Rocker Arm Bearings in Bottom of Oil Pan

After I remove the heads, I remove the valves, clean the heads and inspect the valves, valve seats and springs. I don’t know if the original valve seats are still in the head. The original ones can wear faster than expected due to the removal of Tetra-Ethyl Lead (TEL) from gasoline in the late 1970’s. The heads were bored for dual plugs at some point and it is possible the seats and valves were replaced at that time.

Based on my inspection, I plan to have the heads rebuilt with new seats, valves and valve springs as the valve faces are worn and the springs have sacked. I suspect the seats are original.

Tools

I use a valve spring compressor to remove the valves from the heads. There are a number of different styles of this tool.

Valve Spring Compressor

Valve Spring Compressor

Resources

Here is information about the valves and heads.

Parts

The rocker arm bearings are available at any BMW dealer: (Part#: 11 33 1 261 712). There are two needle bearing cages per rocker so I need eight needle bearings.

Remove Head

This is straight forward. The heads are secured with six nuts, four on each of the four cylinder studs and two at 12:00 and 6:00 that fit on the two studs in the top of the cylinder. If all you need to do is replace the needle bearings in one or more rocker arm assemblies, you can remove the two nuts holding  one rocker assembly leaving the other four nuts holding the head attached, remove the rocker assembly, remove the two old needle bearing cages, install the new ones and then install the rocker arm assembly and torque the two nuts. I’d check the torque on all six of the nuts while I was at it.

Since I am removing the cylinders, pistons and connecting rods and dissembling the valves, I remove the heads completely.

The procedure to remove the heads on the R100RS is the same as for the R75/6. You can read about how to do this here.

There are spots of rust on the right side valve springs, keepers and rocker arm. This fits with the rusty areas I’ve found elsewhere. The bike got parked for sometime and water condensed.

Right Intake Rocker Bushing Has Rust

Right Intake Rocker Bushing Has Rust

Right Intake Valve Spring Pocket Has Rust

Right Intake Valve Spring Keeper Has Rust

Right Intake Rocker Shaft Is Rusty

Right Intake Rocker Shaft Is Rusty

When I remove the rocker arm assemblies,  I put each into a separate zip lock bag and label it so I can put the rocker assemblies back where they came from when I reassemble the heads.

Replace Rocker Arm Needle Bearing Cage

Since there are two bearing cages in the rocker arm, one at the top and one at the bottom, I drive both of them out at the same time. I decide to replace all the rocker arm needle bearings as earlier cages had too small a lip and are prone to this problem.

Here is what the needle bearing cage looks like when all the bearings are inside the cage. There are 31 needles in my needle cage and there is a gap between the bearings that is little less than the diameter of a needle. According to Bob Fleischer in an Email to me:

They’ve been made with 30 (early) and 31 (now) needle rollers, both are fine….the 31 needles version has very slightly smaller diameter rollers.

Left Exhaust Top Rocker Needle Bearings-Note Gap Between Needles at Bottom Which is Normal

Left Exhaust Top Rocker Needle Bearings-Note Gap Between Needles at Bottom Which is Normal

The cage is recessed about 1 mm from the edge of the rocker arm.

Measuring Bearing Cage Recess with Vernier Caliper

Measuring Bearing Cage Recess with Vernier Caliper

Needle Bearing Cage is Recessed 1 mm

Needle Bearing Cage is Recessed 1 mm

When I install the new bearing cages, I’ll recess them the same amount.

I found a socket that was just a bit smaller in diameter than the bearing cage.

Socket Just a Bit Smaller Than Cage Diameter

Socket Just a Bit Smaller Than Cage Diameter

I use a socket extension and mount it backwards into the socket. That way the solid face of the socket is against the bearing limiting the ability to have the socket get cocked and damage the bearing cage.

Socket and Extension Configuration For Driving Needle Bearings

Socket and Extension Configuration For Driving Needle Bearings

I use a 2 Lb mallet to drive the two old bearings out of each rocker arm.I mount the rocker arm in my vise with the rubber jaws. I am careful to keep the arm with the tappet from contacting the vice jaws so I don’t put any force on them when I drive out the bearings. Then I use the socket with an extension and a 2 Lb maul to driver both bearings out of the rocker.

Ready to Drive Bearing Cages Out of Rocker Arm

Ready to Drive Bearing Cages Out of Rocker Arm

I don’t want the new cage to deform nor have the needle bearings fall out while I drive the bearing cage out of the rocker arm. I insert the rocker arm so it’s part way inside the bearing cage.

Using Rocker Arm to Hold Bearings Inside Cage & Prevent Deforming It

Using Rocker Arm to Hold Bearings Inside Cage & Prevent Deforming It

I drive one cage from the top of  the rocker. When the cage is flush with the rocker arm I recess the cage 1 mm by tapping the socket a bit, measuring how far it has moved and repeat until it’s recessed 1 mm. Then I drive the second bearing cage in from the bottom of the rocker and again recess the cage 1 mm.

New Bearing Cage Recessed 1 mm

New Bearing Cage Recessed 1 mm

When both bearings are seated in the rocker arm, I use some engine assembly lube to lubricate the needles and then slide the rocker arm inside the bearing cage to keep the needles in place and put the assembly in it’s labeled bag.

Engine Assembly Lube

Engine Assembly Lube

Putting Engine Assembly Lube on Bearings

Putting Engine Assembly Lube on Bearings

Remove Valves

I use the valve spring compressor to remove each valve from the head. I label four zip lock bags for each valve assembly.

Valve Spring Compressor

Valve Spring Compressor

I adjust the spring compressor so the arm is centered on the face of the valve and the spring collar and then tighten the screw until the spring compresses enough to pop free from the spring collar.

Spring Compressor Pin Centered On Valve Face

Spring Compressor Pin Centered On Valve Face

Spring Compressor Centered on Top Valve Spring Pocket

Spring Compressor Centered on Top Valve Spring Pocket

Valve Spring Compressor Ready To Remove Valve

Valve Spring Compressor Ready To Remove Valve

Here is a complete valve assembly with the bottom and top spring collars, the valve spring, the valve and the two collets that fit into the grooves in the top of the valve stem.

Valve Assembly Components

Valve Assembly Components

Inspect Valves and Springs

I measure the spring height of the uncompressed spring. According to Duane Auscherman’s engine specifications, there are different color springs with different uncompressed spring heights. These springs are “brown” as they have a dab of brown paint on the top of the spring coils.

"Brown" Paint Code on Spring-2nd Coil From Top

“Brown” Paint Mark on Spring-2nd Coil From Top

They are all 45 mm or less. The specification is 45 mm so all of them are ready to replace.

Measuring Valve Spring Uncompressed Height at 45 mm or Less

Measuring Valve Spring Uncompressed Height at 45 mm or Less

The valve face lip can wear. I measure them and find several of the valves have lip thickness as small as 0.5 mm. The valve lips are unevenly worn with part of the lip at 1 mm and part at 0.5 mm. So, new valves are in order.

Portion of Valve Face is 1 mm Thick

Portion of Valve Face is 1 mm Thick

Portion of Valve Face at 0.5 mm

Portion of Valve Face is 0.5 mm

At this point, I plan to have the heads rebuilt with new seats, valves, springs and collets.

4 thoughts on “11 BMW 1977 R100RS Replace Rocker Needle Bearings, Remove Valves & Inspect

  1. THanks for all this info I am about to replace the needle bearings for my R90/6 from 1974 and they are in the freezer, and I intent to heat up the rocket and insert the cold bearing with the axisi inside. I am concerned about pounding too much on the bearing cage. When you state above “I drive one cage from the top of the rocker.” how do you do this specifically? Thanks!

    • Hi Thierry,

      If I recall, I believe I used a suitable socket as the drift to drive the bearing onto the shaft. I show all the details of this in several pictures in the write-up.

      I hope this helps.

      Best.
      Brook.

Leave a Reply to ThierryCancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.