OTRA Day-3: R80 G/S & R65LS 40th Anniversary Rally

Gonzo and I left Hannibal a bit later this morning than I had planned. I had to wait to fill the gas tank in the morning. I usually fill up before stopping for the night, however, I wanted to adjust the front disk brake as I had installed new pads just before leaving. The front brake lever adjustment is done at the front master cylinder which is under the gas tank so I have to remove the gas tank and I wanted to do that with the tank close to empty.

After gassing up on the way out of Hannibal in the morning it was about two miles to the Mark Twain Memorial bridge over the Mississippi river where the state line of Illinois is about half way over the bridge. I stopped on the bridge in the break down lane to get a picture.

Half-way Across The Mark Twain Memorial Bridge

Half-way Across The Mark Twain Memorial Bridge

As I got back to the bike, I could smell gasoline. Looking down at Gonzo’s left carburetor, I could see he was throwing up his morning gas station breakfast all over the bridge.

Gonzo Threw-up On Mark Twain Memorial Bridge

Gonzo Threw-up On Mark Twain Memorial Bridge

I shut off both petcocks, pulled the left float bowl off and tapped up and down on the float to clear whatever was stuck in the float needle. I installed the bowl and turned the petcock back on, and no more fuel leaking, so Gonzo was feeling better. Then, for some reason, I happened to look just ahead of the front tire and low and behold, there was a 10 penny nail about a foot ahead of the tire and pretty much exactly where I would have ridden right over it. I picked it up and added it to all the other treasures on the bottom of the Mississippi river. Gonzo clearly wanted to make sure I didn’t get a flat, and all he could think of to get my attention was to throw up his breakfast in front of me :-). I gave him a “high three” because Gonzo only has three fingers, and we motored off into Illinois.

Giving Gonzo an "Up Top, High 3" :-)

Giving Gonzo an “Up Top, High 3” 🙂

Right after I crossed the bridge, I exited onto Illinois 106 and wound my way through the country-side on shaded two lane roads that cut a tunnel through stands of still green trees; no signs of fall anywhere even though it’s mid-September. By this time, it was 9:15 am and already 83 F, so today is going to be another summer day ride through the humid mid-west.

I came to the Illinois river and, low and behold, it’s still a draw bridge.

A Draw Bridge Over the Illinois River

There aren’t many of these left. I prepared myself for the fun to come and when I got to the section that gets raised, sure enough it was surfaces in “smooth as a baby’s butt” polished steel with all the limited traction that offers. A loose grip on the handlebars and light acceleration is the recipe for success and although Gonzo squirmed around a bit as he looked for traction, we got over that section without much drama. These can be a lot more exciting when it’s raining and there is cross-wind blowing, DAMHIK 🙂

I leisurely rode through a number of small towns and found one in particular had put American flags on every light pole. This scene captures the heart of middle America where people remember to be grateful for the privilege to live in this country despite the mistakes we have made and will continue to make in the future.

Small Town America Street-scape

It’s now in the upper 80’s and as I ride through the middle of a mid-west canyon carved between corn fields by US-36, I come to the Indiana border and loose an hour as I enter the Eastern time zone.

The altitude is about 650 feet, so Gonzo and I are now about 5,000 feet down hill from our home in Colorado. I can see and feel the difference as the sky is more grey-white than blue due to the humidity and 5,000 feet of additional atmosphere on top of us. I always feel like I’m getting too much air when I get down this low, and so does Gonzo as his idle is about 200 RPM too high. I’ll fix that tomorrow morning when I check the oil and the tires before we head out.

I see a couple signs with Ernie Pyle’s name including on a sign for a roadside park. It made me wonder if he was born nearby in Indiana. It turns out he was born in Dana, Indiana, just a bit North of US-36. I knew he also lived in Albuquerque, New Mexico in 1940, as the first branch library in Albuquerque is named after him. I passed it often when I lived in Albuquerque, and stopped in to look at the exhibits.

Who was Ernie Pyle you might ask?  The Albuquerque library has a good biography about him.

One observation about this trip that I want to share is that Dollar Store is now America’s small town retailer. I have seen them in towns as small as 500 population. They seem to have a successful formula of opening modest sized general stores in all the small to mid-size American towns. Wal-mart on the other hand, which started as a small general store in Bentonville, Arkansas, is nowhere to be found in the smaller towns.

Small Town America's Store

Gonzo has been making friends along the way. On the first day, when we were getting gas, an older fellow on a Harley came over to find out what kind of bike I had. He thought it was a distinctive machine and waited for me to start it because “I want to hear what it sounds like.” And the other day in the hotel parking lot, a fellow came over to look at Gonzo and to reminisce about his Yamaha that he sold several years ago. He was curious about the air tubes from the air box and wondered if they got in the way of my legs. I told him they don’t, but they do look as if they would bump into your shins.

Tomorrow we I end the day at the border of West Virginia and Pennsylvania just outside Wheeling, West Virginia in a town with an unusual name, Tridelphia. So far, Gonzo is running well and we both are looking forward to wandering our way across the rest of Indiana and Ohio on US-36 and various state highways until we come to the end of US-36 in Uhrichsville, Ohio.

OTRA Day-2: R80 G/S & R65LS 40th Anniversary Rally

Today is a shorter day, which is a good thing as yesterday was a bit long due to the time spent visiting the St. Francis Motorcycle Museum.  I stayed at the Super 8 in Belleville KS, which was pretty deserted. Nonetheless, a number of guests thought it was acceptable to turn up the volume on their truck radio in the parking lot at 12:30 am and stage a parking lot dance while singing along with the tunes.  What ever happened to being considerate and aware of your surroundings?  Any how, I have ear plugs for just such idiots.

On Sunday morning, I started for Hannibal, MO about 9:00 am. But before I left I got to use the wash cloth I packed to wipe the water off the seat.  Yes, I’m officially in the mid-west where a dry day is 60% humidity. 🙂

[BTW, I pack a spray bottle of hydrogen peroxide and a wash cloth. I spray the windscreen and fairing with the peroxide and in 60 seconds or so, all the bug guts and goo dissolve and are easy to wipe right off. It doesn’t affect the paint or the plastic, so this is now in my “On The Road Again (OTRA)” kit.]

US-36 becomes the “Pony Express Highway” in the Eastern part of Kansas. In Marysville, there is a pony express stable, but being Sunday, it was closed. I got a picture of my “express horse”, Gonzo, in front.

A Pony Express Station From 1860 in Marysville, KS

A Pony Express Station From 1860 in Marysville, KS

I crossed over the border into Missouri. By this point, US-36 becomes a 4-lane divided highway with county roads cutting across it via the median.

Crossing Into Missouri at St. Joseph

Crossing Into Missouri at St. Joseph

Along the way, I rode through a large wind turbine farm among the Missouri corn fields. This reminds me of the eastern Colorado farmers who first let oil wells sprout among the corn and wheat in their fields and now are planting large numbers of wind turbines.

Wind Turbines Let Missouri Farms Harvest Wind & Corn

Wind Turbines Let Missouri Farms Harvest Wind & Corn

Then, I unexpectedly came upon the hometown of the great WW1 General, John “Black Jack” Pershing in Laclede, MO.  I was vaguely familiar with some of his story as I lived in Las Cruces, New Mexico, as a young boy, not far from Columbus, New Mexico. Poncho Villa raided Columbus in 1916 shortly after New Mexico became a state in 1912. I believe this is the only foreign invasion of the United States. Pershing, who was based at Fort Bliss in El Paso, Texas, went after him chasing him in Mexico (and it turns out Patton, who was a Lt. under Pershing, participated too) , but were not able to find him. So, now I know where he was born.

John "Black Jack" Pershing Home Town in Laclede, MO

John “Black Jack” Pershing Home Town in Laclede, MO

The next surprise was seeing the Missouri highway department harvesting hay in the median of US-36. Now that’s a cool idea IMHO.  Why waste that land when you can harvest feed for horses and cattle.

US-36 Median Grass Is Harvested by The Highway Department for Hay

US-36 Median Grass Is Harvested by The Highway Department for Hay

Hannibal, Missouri-Home of Mark Twain

I got to Hannibal about 3:00 pm and it was about 92 F, so I’m still riding in summer weather. I again stayed at the Dubach Inn and ended up in the same room I stayed in in 2017.

When I stayed here on the 2017 ride, I spent a lot of time visiting the Mark Twain Museum and wrote about that in my blog about that trip. This time, I decided to hike around town and see some of the sights I missed last time.

Gonzo Resting In Front of the Dubach Inn, Hannibal MO

Gonzo Resting In Front of the Dubach Inn, Hannibal MO

Dubach Inn, Hannibal MO

Dubach Inn, Hannibal MO

After getting a shower and having my traditional end-of-ride libation (Gin & Tonic) I headed out to explore. I found out that 2019 is the bi-centennial of the founding of Hannibal in 1818. Another unexpected discovery.

2019 is 200th Anniversary of the Founding of Hannibal, MO

2019 is 200th Anniversary of the Founding of Hannibal, MO

Hannibal also added pennants on the lampposts commemorating citizens who served in the military. I saw the same thing when I visited Omaha Beach in France where Allied soldiers were commemorated.

Similar to Solider Remembrance I Saw At Omaha Beach in France

Similar to Solider Remembrance I Saw At Omaha Beach in France

Similar to Solider Remembrance I Saw At Omaha Beach in France

Similar to Solider Remembrance I Saw At Omaha Beach in France

I found a lighthouse that is dedicated to Mark Twain and climbed up to it. I needed another shower after that. 🙂

Mark Twain Memorial Lighthouse

Mark Twain Memorial Lighthouse

Mark Twain Memorial Lighthouse

Mark Twain Memorial Lighthouse

Mississippi River View From Lighthouse Hill

Mississippi River View From Lighthouse Hill

On my way back from walking along the bluff above the Mississippi river, I saw something along the side of the path. It was just my good luck to come along when I did I guess.

Hmm ... What's That?

Hmm … What’s That?

I guess this shows money really does grow on trees. 🙂

My Reward For Climbing Mark Twain Lighthouse Hill :-)

My Reward For Climbing Mark Twain Lighthouse Hill 🙂

And I came across this fellow. Some days are like that, but not this one for me. 🙂

Some Days, You Feel Like This

Some Days, You Feel Like This

At the bottom of the stairway to the lighthouse I stumbled upon two plaques commemorating the building of the first Mark Twain memorial bridge in 1935 and the replacement of it by the current one in 2000.

Original Mark Twain Bridge Plaque

Original Mark Twain Bridge Plaque

Replacement Mark Twain Bridge Plaque

Replacement Mark Twain Bridge Plaque

The Replacement Mark Twain Memorial Bridge

The Replacement Mark Twain Memorial Bridge

Mississippi River View From Lighthouse Hill

Mississippi River View From Lighthouse Hill

Downtown Hannibal From Lighthouse Hill

Downtown Hannibal From Lighthouse Hill

Another block or two brought me to the Mark Twain Brewing Company. I stopped in and sampled a couple of their excellent beers and had my supper.

Mark Twain Brewing Company-Good Beer and Food

Mark Twain Brewing Company-Good Beer and Food

Tomorrow I cross the Mississippi and cross Illinois on my way to the east side of Indianapolis.

Here is a slide show of today’s ride pictures.

OTRA Day1: R80 G/S & R65LS 40th Anniversary Rally

I left on Saturday morning joined by two friends, Chris and John, who decided to ride along to the St. Francis Motorcycle Museum in St. Francis, Kansas. I noticed a sign for it when I took US-36 to the 2017 R100RS 40th Anniversary Rally, but didn’t feel like I had the time to stop.  The museum is about 200 miles from metropolitan Denver, so it’s about the half-way mark for today’s route which ends in Belleville, KS.

As last time, US-36 is a lightly traveled road in excellent condition with almost no 18-wheelers. The traffic this time was about twice as much as the 2017 trip because I left on Sunday that time and most of Kansas stays home on Sunday. But it was light traffic nonetheless and made for a relaxing ride.

Kansas Border

Kansas Border

Kansas Border-Brook & John

Kansas Border-Brook & John

Kansas Border-Chris & Brook

Kansas Border-Chris & Brook

St Francis Motorcycle Museum

What an enjoyable collection of turn of the 20th century American motorcycles from the numerous manufacturers in business before WWI and the later Great Depression. As is the case with the computer revolution of the middle part of the 20th century, which had a large number of computer hardware companies, the American motorcycle industry consolidated over the next 50 years into a handful of companies. The collection was a delight and even included two BMW’s, an R60S and an R27.

St. Francis Motorcycle Museum Decal

St. Francis Motorcycle Museum Decal

St. Francis Motorcycle Museum-1966 R69S

St. Francis Motorcycle Museum-1968 BMW R69S

St. Francis Motorcycle Museum-1968 BMW R69S

St. Francis Motorcycle Museum-1968 BMW R69S

St. Francis Motorcycle Museum

Geographic Center of the US

After I left John and Chris in Bird City where they turned off to visit a good friend of John’s before heading back home, I continued for another 200 miles to Belleville KS. Not too far from there is the geographic center of the US. Although I didn’t exactly go to the exact spot, I did take some pictures of the memorial to it on US-36.

Geographic Center of The USA

Geographic Center of The USA

Days Slide Show

Here is a slide show of the days pictures, mostly of the fabulous motorcycles on exhibit in the museum.

On The Road Again (OTRG)… R80 G/S & R65LS 40th Anniversary Rally

Gonzo (my 1977 R100RS) and I are going to be on the road again on our way to Todd Trumbore’s home where he is hosting his third airhead 40th anniversary celebration of bikes designed by the legendary Hans Muth, on September 19-22, in Harleysville, PA. (Yes, an ironic location for a BMW airhead rally 🙂 ) This time Todd is celebrating 40 years since the introduction of the iconic R80 G/S and the R65LS models in 1979. Once again, Hans will be in attendance along with a notable list of other airhead and motorcycle legends who will be speaking.  You can see the details here:

–> 40TH ANNIVERSARY RALLY TO CELEBRATE LEGACY OF R 65 LS, R 80 GS

R 80 G/S Started the Adventure Bike Category

R65 LS – Distinctive, Minimalist Styling

The first rally Todd hosted was in 2014 for the R90S and the second was in 2017 for the R100RS, which is the rally Gonzo and I first attended. Even though my garage does not yet include an R80 G/S or R65LS, Todd was happy to let me attend the festivities despite riding “only” an RS.

The R80 G/S and R65LS are the last two designs Hans developed for BMW before starting a design studio, Target Design, with some friends, Jan Fellstrom and Hans-Georg Kasten. One notable design from the Target Design studio was the Suzuki Katana in 1980. I find the lines of the R65LS and Katana are similar, as if Hans extended the design vocabulary the BMW R65LS and to the design commissioned by Suzuki for the Katana.

Suzuki Katana-To Me, It Echos The Design Vocabulary of the R65LS

When Gonzo and I went out in 2017, we had an adventure when the shift cam retaining circlip in Gonzo’s transmission came off the shaft. The BMW dealer I ordered it from supplied the wrong size circlip and I was not attentive enough to notice. Gonzo and I ended up being transported to the rally hotel by Scott Mercer with assistance from Tom Gaiser, and Keven O’Neil. Tom Cutter, at Rubber Chicken Racing Garage, one of the best airhead transmission re-builders, was a speaker at the rally and put Gonzo on his trailer while I followed him to his shop riding his “most excellent” R100 “Fake S” bike. He took apart the transmission on the Sunday after the 2017 rally while I watched and assisted with cleaning parts, and I was back on the road that Monday. Here is the story of my adventures going to the 40th anniversary of the RS rally in September 2017.

Although Gonzo and I are very appreciative of Tom’s generous assistance. we plan to avoid imposing on him again on this trip. 🙂

Since I \didn’t complete the entire trip last time in 2017, I am going to take the same route out and back this time. Somehow that seems appropriate.

Gonzo now has “matte” clear coat, which is correct for the 1977 RS bikes, but due to my failure to communicate with my painter, he was repainted with gloss clear coat back in 2017 when I did the restoration. He is also sporting the commemorative badge Todd provided to the participants of the 2017 R100RS rally. I think it’s a very nice touch and a lot classier than the cheap decal BMW originally used on the cowling in 1977.

Gonzo ‘s Matte Clear Coat and Commemorative 40th RS Rally Badge

Rear Cowl With Original "Cheap" Decal BMW Used in 1977

Rear Cowl With Original “Cheap” Decal BMW Used in 1977

Gonzo and I are looking forward to attending this last of the 40th anniversary celebrations of Hans Muth designed BMW motorcycles.

Gonzo’s Excited to Go To Another Todd Trumbore Hosted 40th Anniversary Rally

1983 BMW R100RS Rebuild Master Cylinders & Brembo Calipers

This bike has a front master cylinder that is integrated into the Magura throttle assembly and a rear Brembo master cylinder. All three calipers are Brembo F-08 series with dual 38 mm pistons.  I disassembled both master cylinders and inspected them. I repainted and rebuilt the rear master cylinder using a Brembo rebuild kit. Unfortunately, I found the front Magura master cylinder bore and internals were badly rusted and pitted, so I had to replace the front master cylinder rather than rebuild it. Even though I didn’t have to rebuild the front master cylinder, I show how you rebuild it and the rear master cylinder in this document.

I also put together two short videos showing the work I did on the front and the rear master cylinders.

1983 R100RS Disassemble & Inspect Front Master Cylinder

1983 R100RS Disassemble, Inspect & Rebuild Rear Master Cylinder

I removed the brake calipers when I removed the brake system and you can see how to remove the calipers here:

I disassembled all three calipers, inspected them and found they were not corroded or pitted so I repainted and rebuilt them using a Brembo caliper rebuild kit. The same kit is used on all three calipers. You can see how I did that work here:

I also put together a video about how I rebuilt the calipers.

1983 R100RS Disassemble, Inspect & Rebuild Brembo Brake Calipers